basic unit

Kampmann Katherm HK trench heater, ready-to-install floor trench, either for installation in raised or screeded floors, convector-based for heating and cooling with tangential fan convection. Heat and cooling outputs tested in accordance with E DIN EN 16430, parts 1 to 3. Hygiene-certified in line with VDI 6022.
Trench chassis made of sendzimir galvanised sheet steel, coated in graphite gray on both sides. Height-adjustable on the sides using mounting aids, with impact sound insulation; features a sturdy height-adjustment mechanism with impact sound insulation, for secure mounting of the duct. With pre-punched openings for water supply and return as well as electrical connections, on the room side. Trench chassis prepared for condensate pump mounting kit. Segmented sheets serving as both finger protection for the tangential fan and a mounting frame for the filter fleece, air-guidance sheet, grate support, and cross-brace for reinforcing the duct. Center wall serving as both an air-guidance sheet and a mounting plate for the tangential fan.
Life Cycle Assessment (LCA) data is published in the form of an EPD according to EN 15804 and is available to download from the International EPD System. Registered in the building products platform DGNB Navigator. GWP (phase A1-A3), kg CO2 Äq.1,01E+02. Further calculations possible online.

Heat exchanger

High-performance heat exchanger made of circular copper pipes with aluminum fins and a Eurokonus valve connection, coated in graphite gray. Features an anti-rotation device. Collector with integral bleed option.

System		4-pipe
Max. operating pressure	bar	10
Max. entering water temperature	°C	95
Min. entering water temperature	°C	5
Max. air inlet temp.	°C	40
Max. glycol volume	%	50

Condensate tray

Condensate tray has a flow-optimised design, for the simultaneous discharge of condensate and air guidance below the convector. Condensate tray designed as an independent component that can be removed for cleaning and maintenance in accordance with VDI 6022.

Fan

Tangential fan with safety guard. Energy-saving EC fan with 0-10 V input for continuously variable speed control with sound-optimised commutation electronics. Valve controlled via 24 V DC control contacts. All rotating parts have low-noise and maintenance-free bearings. Motor monitoring with internal fault processing.
Even flow through the convector, low power consumption for effective, energy-saving consumption, also sound-optimised for low sound values. Easily removable for cleaning and maintenance due to combined coupling/ball joint system with simultaneous acoustic decoupling. With sound-optimised commutation electronics Factory-wired ready for connection. Valve controlled via 24 V DC control contacts.

Control

• Built-in KaControl MC controller for continuous fan control with motor monitoring.
• For the control of 24 V DC actuators (Open/Closed) for heating and cooling operation.
• With connection option for 5 multifunctional inputs (room temperature, window contact, supply and return temperature, heating/cooling changeover, condensate alarm, sequential control via a 0-10 V signal etc.), unit-specific control and regulation algorithms with the core functions of room temperature control (heating/cooling).
• Timer program with battery-backed real-time clock for four operating modes (Day/Eco/Extra/Off), commissioning function.
• Grouping of up to 10 units and a display to create a control zone using CAN-bus, automatic addressing and communication monitoring of all bus subscribers, continuous synchronisation of all statuses and parameters within the group.
• CAN bus interface and galvanically isolated RS485 interface, each with two terminal blocks for separate connection with daisy chain cabling with a switchable terminal resistor.
• connection of central functions, such as heating cooling changeover to a freely selectable unit within the group.
• Ethernet interface with two RJ45 sockets with built-in switching function.
• KNX-TP interface with socket terminal, all terminals are designed as plugs, wireless communication via Wi-Fi web server for user-friendly operation and for complete password-protected parametrisation.
• protocols can be unlocked via licences: BACnet/IP, Modbus TCP, Modbus RTU, KNX.

Grille

With frame insert profile, colour-coordinated to the grille. With protective installation cover and frame trim. With cover panels for connection areas. With double T-profile grille. Connections made of corrosion-proof steel springs with matching spacers.

Configuration

Grille design		Roll-up grille
Grille finish		Aluminium, natural anodised
Connection		Eurokonus, opposite end, cooling connection side on left, heating connection side on right
Length	mm	1200
Width	mm	360
Height	mm	210
Bar height	mm	18
Bar depth	mm	5
Bar spacing	mm	12
Free area, approx.	%	70
Weight	kg	31.3